The Fenix WT16R is a flat rechargeable LED work light that combines a forward-facing beam, a wide side light and a flashing yellow light.
The Fenix WT16R is a flat rechargeable LED work light that combines a forward-facing beam, a wide side light and a flashing yellow light. The focused beam reaches up to 115 m, while the COB floodlight is suitable for illuminating a nearby work surface. Magnets on the back and base of the body provide two ways to attach the light while working. Suitable for Maintaining cars, machinery and equipment Illuminating workbenches, engine compartments and electrical cabinets Quick inspections in garages or warehouses Installation and repair work in confined spaces Marking a work area with the flashing yellow light Why choose the Fenix WT16R? Switch between focused and floodlight modes with a single button. Two magnets help secure the light in different positions. A steel clip keeps the light handy on the edge of a tool bag or pocket. The 30 lm focused beam runs for up to 30 hours on a single charge. The charge indicator lets you check the battery level even when the light is switched off. Technical specifications Manufacturer: Fenix Light sources: 2 × Cree XP-E2 LEDs and COB side light Focused beam, low: 30 lm, up to 35 m, up to 30 hours Focused beam, medium: 100 lm, up to 65 m, up to 9 hours and 20 minutes Focused beam, high: 300 lm, up to 115 m, up to 3 hours and 50 minutes Floodlight, low: 100 lm, up to 14 m, up to 9 hours and 20 minutes Floodlight, high: 300 lm, up to 23 m, up to 3 hours and 50 minutes Flashing yellow light: 10 lm Battery: built-in 2000 mAh lithium-polymer battery Charging: USB-C Charging time: approximately 1 hour and 40 minutes with a 5 V / 2 A adapter Attachment: magnets on the back and base, steel clip Protection rating: IP66 Drop test: 1 m Dimensions: 127 × 37 × 26 mm Weight: 129 g including battery Runtime in high modes includes operation at reduced light output. Included Fenix WT16R work light USB-C charging cable Wrist strap User manual and warranty card Frequently asked questions How do I switch between the focused beam and floodlight on the WT16R? With the light on, hold the button down for about 1.2 seconds. Press briefly to cycle through the brightness levels of the selected light mode. How do I turn on the flashing yellow light? Select the floodlight and press briefly to cycle through the modes until you reach the flashing yellow light. How can I use the WT16R when there is no steel surface nearby? Stand the light on its base on a flat surface or use the clip on the body to attach it to the edge of a suitable pocket or piece of equipment. When is the Fenix WT16R the right choice? The WT16R is a good choice when you move from an inspection to a repair and need both a focused beam for longer distances and a stationary light for close-up work. If the light needs to follow your gaze continuously while you work, a headlamp is more convenient. Our recommendation When working on a machine, position the light so that the COB side light covers the work area and the magnet rests on a flat steel surface. For a shiny component, move the light a few centimetres to the side until the reflection no longer obstructs your view. If you are looking for a fault deeper inside the equipment or illuminating a walkway, switch to the focused beam. For a longer repair, try the 100 lm floodlight first. It often provides enough light for close-up work while saving battery power for the next job. Before putting the light in your tool bag, switch it off and lock it with a double press. If you use the light at several work sites, check the battery level before moving on to the next task and keep the charging cable in a secure place in your tool bag. One work light for inspections and repairs The Fenix WT16R provides a focused beam for walkways and a wide beam for work surfaces. The magnets and clip help position the light wherever it is needed.
The Fenix WT16R is a flat rechargeable LED work light that combines a forward-facing beam, a wide side light and a flashing yellow light. The focused beam reaches up to 115 m, while the COB floodlight is suitable for illuminating a nearby work surface. Magnets on the back and base of the body provide two ways to attach the light while working. Suitable for Maintaining cars, machinery and equipment Illuminating workbenches, engine compartments and electrical cabinets Quick inspections in garages or warehouses Installation and repair work in confined spaces Marking a work area with the flashing yellow light Why choose the Fenix WT16R? Switch between focused and floodlight modes with a single button. Two magnets help secure the light in different positions. A steel clip keeps the light handy on the edge of a tool bag or pocket. The 30 lm focused beam runs for up to 30 hours on a single charge. The charge indicator lets you check the battery level even when the light is switched off. Technical specifications Manufacturer: Fenix Light sources: 2 × Cree XP-E2 LEDs and COB side light Focused beam, low: 30 lm, up to 35 m, up to 30 hours Focused beam, medium: 100 lm, up to 65 m, up to 9 hours and 20 minutes Focused beam, high: 300 lm, up to 115 m, up to 3 hours and 50 minutes Floodlight, low: 100 lm, up to 14 m, up to 9 hours and 20 minutes Floodlight, high: 300 lm, up to 23 m, up to 3 hours and 50 minutes Flashing yellow light: 10 lm Battery: built-in 2000 mAh lithium-polymer battery Charging: USB-C Charging time: approximately 1 hour and 40 minutes with a 5 V / 2 A adapter Attachment: magnets on the back and base, steel clip Protection rating: IP66 Drop test: 1 m Dimensions: 127 × 37 × 26 mm Weight: 129 g including battery Runtime in high modes includes operation at reduced light output. Included Fenix WT16R work light USB-C charging cable Wrist strap User manual and warranty card Frequently asked questions How do I switch between the focused beam and floodlight on the WT16R? With the light on, hold the button down for about 1.2 seconds. Press briefly to cycle through the brightness levels of the selected light mode. How do I turn on the flashing yellow light? Select the floodlight and press briefly to cycle through the modes until you reach the flashing yellow light. How can I use the WT16R when there is no steel surface nearby? Stand the light on its base on a flat surface or use the clip on the body to attach it to the edge of a suitable pocket or piece of equipment. When is the Fenix WT16R the right choice? The WT16R is a good choice when you move from an inspection to a repair and need both a focused beam for longer distances and a stationary light for close-up work. If the light needs to follow your gaze continuously while you work, a headlamp is more convenient. Our recommendation When working on a machine, position the light so that the COB side light covers the work area and the magnet rests on a flat steel surface. For a shiny component, move the light a few centimetres to the side until the reflection no longer obstructs your view. If you are looking for a fault deeper inside the equipment or illuminating a walkway, switch to the focused beam. For a longer repair, try the 100 lm floodlight first. It often provides enough light for close-up work while saving battery power for the next job. Before putting the light in your tool bag, switch it off and lock it with a double press. If you use the light at several work sites, check the battery level before moving on to the next task and keep the charging cable in a secure place in your tool bag. One work light for inspections and repairs The Fenix WT16R provides a focused beam for walkways and a wide beam for work surfaces. The magnets and clip help position the light wherever it is needed.
